#### [[返回文档目录]](../index.html) [[查看原始页]](../content/Raspberry%20Pi%E5%AE%89%E8%A3%85%20Archlinux.html) # Raspberry Pi安装 Archlinux *本帖最后由 GeekNapster 于 2012-12-31 15:04 编辑* 由于是用英文写的。大家凑合着看了。道理简单。 本人半个小时原创，呵呵～ Archlinux纯净版安装。原标题 Install Archlinux on Raspberry Pi as you wish! The easiest way to install archlinux on raspberry PI. now you need to input these command promotes. **[plain]** view plaincopy - dd if=/home/xx/Downloads/archlinux.img of=/dev/sdX bs=2M then you need to plug the SD card into raspberry Pi Then boot By default, the user name and password are both "root" After logging in, you need to check out all your devices with command promotes : **[plain]** view plaincopy - fdisk -l /dev/mmcblk0 then you will find there are two partitions down there by default for archlinux installation. The first one is /dev/mmcblk0p1 which is the "/boot" folder whose format is fat32. The second partition is /dev/mmcblk0p2 which is the "/" folder whose format is ext4. Now we need to use the rest free space of the SD card disk. So, we input those commands : **[plain]** view plaincopy - cfdisk /dev/mmcblk0 Using cfdisk to mange the partition label of the SD card. Also we could use fdisk. But fdisk needs us to give the specific bytes to make the partition room, which is too precise. Anyway both cfdisk and fdisk make sense. now we make a 1GB room for swap, and the rest for folder "/home" TIPS:         Now if we use **[plain]** view plaincopy - fdisk -l /dev/mmcblk0 we will only see two partitions those which are /dev/mmcblk0p1 and /dev/mmcblk0p2.       We can't see the other two partitions /dev/mmcblk0p3, /dev/mmcblk0p4 those which we have divided from the rest free space of the SD card.        All we need is to reboot the raspberry pi. **[plain]** view plaincopy - reboot then **[plain]** view plaincopy - fdisk -l /dev/mmcblk0 **[plain]** view plaincopy - [root@alarmpi ~]# fdisk -l /dev/mmcblk0 - Disk /dev/mmcblk0: 15.9 GB, 15931539456 bytes - 4 heads, 16 sectors/track, 486192 cylinders, total 31116288 sectors - Units = sectors of 1 \* 512 = 512 bytes - Sector size (logical/physical): 512 bytes / 512 bytes - I/O size (minimum/optimal): 512 bytes / 512 bytes - Disk identifier: 0x000c21e5 - Device Boot      Start         End      Blocks   Id  System - /dev/mmcblk0p1   \*        2048      194559       96256    c  W95 FAT32 (LBA) - /dev/mmcblk0p2          194560     3862527     1833984   83  Linux - /dev/mmcblk0p3         3862528     5862527     1000000   82  Linux swap / Solaris - /dev/mmcblk0p4         5862528    31116287    12626880   83  Linux now we can get all those partitions. Now we need to have swap and format the partition /dev/mmcblk0p4 **[plain]** view plaincopy - mkswap /dev/mmcblk0p3 - swapon /dev/mmcblk0p3 - mkfs.ext4 /dev/mmcblk0p4 now we need to edit the /etc/fstab make it like this: **[plain]** view plaincopy - # - # /etc/fstab: static file system information - # - # <file system>        <dir>         <type>    <options>          <dump> <pass> - devpts                 /dev/pts      devpts    defaults            0      0 - shm                    /dev/shm      tmpfs     nodev,nosuid        0      0 - /dev/mmcblk0p1  /boot           vfat    defaults        0       0 - /dev/mmcblk0p2  /               ext4    defaults        0       0 - /dev/mmcblk0p3  none            swap    defaults        0       0 - /dev/mmcblk0p4  /home           ext4    defaults        0       0 Alright. Now we make it. We need to upgrade the archlinux syntactically. So we need to edit the file **[plain]** view plaincopy - vi /etc/pacman.d/mirrorlist then, uncomment the links below if the place is supposed near your location.   then **[plain]** view plaincopy - pacman -Sy Now we need to set our localtime and locale. so we need to uncomment /etc/locale.gen if there is a locale you want to have.  *（外链图片未本地化）* And **[plain]** view plaincopy - ln -sf /usr/share/zoneinfo/Asia/Shanghai /etc/localtime (because i am in China, so it's Shanghai. It depends on where you are.) Also, you could change /etc/hostname, or never mind. Now you need to add a new user you could use : **[plain]** view plaincopy - adduser and you could install sudo **[plain]** view plaincopy - pacman -S sudo Then edit the file sudoers by commands **[plain]** view plaincopy - sudo visudo then, add the line "USER ALL = (ALL) ALL" below the line root ALL = (ALL) ALL Now reboot your computer. It is a clean and fast one. Or you want to install video driver or get into serial console. https://wiki.archlinux.org/index.php/Raspberry#Installation At the bottom of the page, those reference maybe help. Cheers! [Raspberry Pi](thread-5812-1-1.html)